Open 5am - 10pm Daily 401 749-3474
4:30 am -10pm Sat, Sun & Holidays
Ice Fishing Safety Tips Ice Thickness and Strength for Varied Loading Conditions
RI Dem Ice Safety Hotline Ice Thickness Strength Ratings

ICE SAFETY GUIDE

The RI DEM Division of Parks and Recreation tests only the designated areas at the following locations for safe ice:

Goddard State Park ( Ice Skating Area ) Warwick RI
Lincoln Woods State Park Lincoln, R.I.
Meshanticut State Park Cranston Rhode Island

RI DEM ICE SAFETY HOTLINE

DEM's 24-hour ice safety hotline at 401- 222-2632

Ice Thickness and Strength
for Various Loading Conditions


Every winter it becomes very important to know when the ice is safe to use. Here are some guidelines for determining the safety of freshwater ice. The following table of safe loads is valid ONLY for ice that is clear and sound, with no flowing water underneath. it is not reliable for stationary loads. When in doubt, stay off the ice !

You should Ice Fish with a Partner unless you are certain there are other ice fishermen in the area you will be fishing. Use headlamps if you plan to be on the ice before sunrise or within an hour of sunset. Never go to a new ice fishing pond or lake for the first time before sunrise unless you are certain that there is safe ice.

Loads on Ice

 

Required Minimum Ice
Thickness in inches
Description of
Safe Moving Load
1-3/4 One person on skis
2 One person on foot or skates
3 One snowmobile
3 A group of people walking single file
7 A single passenger automobile
8 A 2-1/2 ton truck
9 A 3-1/2 ton truck
10 A 7 to 8 ton truck

What you need to know

Because there can be many variations in the structure, thickness, temperature and strength of an ice sheet, it is essential to carry out some fairly simple field observations of the ice sheet you want to use to support a load. Be cautious! Never go out on an unknown ice sheet alone, and always probe ahead of yourself with a heavy ice chisel. Consider wearing a personal flotation device and roping yourself to an assistant.

The main thing to determine is the ice thickness. This can be done by drilling holes with an ice auger. Note whether the ice is clear (sometimes called black ice) or white (due to air bubbles sometimes called snow ice). Measure the thickness of both kinds. Take note of the frequency of cracks and whether they are wet or dry. On rivers, be alert to variations in ice thickness that may occur as a result of bends, riffles or shallows, junctions with tributaries, etc. Ice Thickness varies near shore, rocks or submerged logs due to the rocks and shores absorbing and radiating the sun's warmth into the adjacent water.

For both rivers and lakes, warm inflows from springs may create areas of thinner ice. Also, the ice thickness near shore may be thinner (due to warm groundwater inflow or the insulating effect of drifted snow) or thicker (due to the candle-dipping effect of variable water levels).

Observe any snow cover as well as variations in its thickness. Obtain the record of air temperature for the past several days, and continue observing air temperatures during the period the ice will be used to support loads.

Contrary to what many think, a rapid and large air temperature drop causes an ice sheet to become brittle, and the ice may not be safe to use for 24 hours.

If the air temperature stays above freezing for 24 hours or more, the ice begins to lose strength, and the table no longer represents safe conditions. This becomes the general condition in the spring. Even though the ice may have adequate thickness, the strength is quickly lost the longer the air temperature is above freezing. In all cases of air temperature changes, the effects are greatest on bare ice, and are subdued by increasing depths of snow cover. However, no quantitative guidance can be offered.

Other considerations

An ice sheet must be supported by water. Sometimes, near a riverbank, the water level will drop after the initial ice sheet is formed, leaving the ice sheet unsupported near the shore. This occurrence can be detected by hearing a hollow sound when probing with an ice chisel. Naturally this is not a safe location for loads on the ice.

Cracks in the ice are either wet or dry. If dry, they do not penetrate the ice sheet and are not a problem. If they are wet, multiply the vehicle class by 2 to obtain the required minimum ice thickness. Also, drive across the cracks as close to perpendicular as possible, instead of parallel to them.

On thicker ice with very heavy loads, radial cracks may be observed originating from the center of the load. This usually occurs at about one-half of the failure load. After the radial cracks develop, circumferential cracks will form and the ice sheet will fail. If radial cracks are seen, the load should be moved immediately. Because ice will creep, it is only a matter of time before the ice fails. The same process happens with thinner ice at breakthrough loading, but the process occurs so much faster that it cannot be relied upon for any warning.


Ocean State Tackle
430 Branch Avenue
Providence, RI 02904
USA

SECURE SHOPPING CART

PayPal is the secure payment processing service we use to collect payments.

Secure Online Shopping

Privacy Protected

Rods Warranty

 
Ocean State Tackle.com
 
 
 
Ocean State Tackle
430 Branch Ave
Providence , Rhode Island
 

401 749-3474

Open Daily  5am - 9pm
Friday- Saturday - Sunday
&
Holidays
5am - 10pm
Subscribe to the Newsletter
I have read and agree to the Privacy Policy

  

 We take PayPal, Master Card, Visa, AMEX and Discover

 

 

 

 

St Croix  Warranty

 

 

 

 

© Copyright  2017 Ocean State Tackle. All rights reserved. 

statistics for vBulletin